The Fundamentals of Plumbing Knowledge When Installing a Bathtub
The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Blog Article
They are making several great observations relating to A Step-by-Step Guide to Installing a Bathtub in general in the content down the page.
Mounting a bath tub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a moderately difficult task. If the old bathtub is readily accessible, the job can move speedily; if you have to open up a wall surface to eliminate the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to take into consideration employing one before you begin. Opportunities are you may need a professional plumber to make tube links.
This post will help you install a new bathtub in your shower room if you have already gotten a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your devices as well as product checklist ought to consist of the following:
Getting ready for the Installment
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap features a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets unit to stop strain on the tub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its last placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is detach the water system. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited accessibility that is often the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, use the same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning throughout this process. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the required setting. The wooden boards are handy in equally spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bathtub up until the level checks out level.
To set up faucets, fit all-time low of the furthest versatile tap connector to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet and the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub must wait up until the bath tub has actually been used a minimum of once as this will resolve it right into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will need reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former type needs to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to break a stiff seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and installations. They are offered in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that article about Tools You Need to Install a New Bathtub when doing a search on the internet. I beg you take a moment to distribute this blog posting if you appreciated it. Thanks for your time spent reading it.
Learn More Report this page